Pressure Washer Hose
Crushproof Suction Hose
Rampage BEAST Pressure Washer Hose
Clear Vinyl Braided Hose
- Featured
- Most relevant
- Best selling
- Alphabetically, A-Z
- Alphabetically, Z-A
- Price, low to high
- Price, high to low
- Date, old to new
- Date, new to old
Recently Viewed Products
How to Choose the Right Pressure Washer Hose
The right pressure washer hose depends on where it sits in your system. A line running from the machine to the gun has to hold thousands of PSI without ballooning. A line pulling from a buffer tank sees vacuum instead, so it has to stay rigid enough that the pump can't suck it shut. Low-pressure chemical transfer lines have a different problem entirely: PSI barely matters, but chemical compatibility does. Pick by job first, then size to your machine.
Match the hose to its job
High-pressure discharge hose (machine to gun) needs steel wire reinforcement and a pressure rating well above your pump's max PSI. Suction hose (tank to pump inlet) needs a rigid spiral that resists collapse under vacuum and won't kink when you drag it across a job site. Transfer hose (low-pressure chemical or water movement) needs braided reinforcement and chemical compatibility, but the PSI rating barely matters.
Size by PSI and GPM
For high-pressure discharge, your hose's working pressure rating must exceed your machine's max PSI with margin to spare. Run a 4,000 PSI machine on a 4,000 PSI hose and you'll see failures fast. Heat, vibration, and pump pulsing all stack on top of static pressure, and a hose rated right at the line can't take that for long. For diameter, 3/8" handles most contractor pressure washers up to about 8 GPM. Step up to 1/2" for higher-flow rigs or long hose runs where pressure drop matters.
Single wire vs. double wire
Single wire reinforcement is lighter, more flexible, and rated for residential and light commercial work, typically up to about 4,300 PSI in 3/8". Double wire adds a second layer of steel braid for higher pressure ratings (up to 7,300 PSI in 3/8") and longer service life on rough job sites. If you're running concrete, gravel, or commercial work day after day, double wire pays for itself.
Pressure Washer Hose by Job
| Job | Recommended hose |
|---|---|
| High-pressure discharge (machine to gun) | Rampage BEAST Pressure Washer Hose |
| Suction / feed line from a buffer tank | Crushproof Suction Hose |
| Low-pressure chemical or water transfer | Clear Vinyl Braided Hose |
Rampage BEAST Sizing Chart
| Machine pressure rating | Recommended BEAST option |
|---|---|
| Up to 4,000 PSI | 3/8" Single Wire (rated 4,300 PSI) |
| 4,000-6,000 PSI | 1/2" Double Wire (rated 6,200 PSI) |
| 6,000+ PSI / heavy commercial | 3/8" Double Wire (rated 7,300 PSI) |
Related Categories
Frequently Asked Questions
What PSI rating do I need for my pressure washer hose?
Your hose's working pressure rating should sit above your machine's max PSI with some headroom. Pressure pulses from the pump, heat buildup, and routine abrasion all chip away at the rated pressure over time, so a thin margin fails fast. Use the sizing chart above to match a Rampage BEAST option to your machine.
Should I use a 3/8" or 1/2" pressure washer hose?
3/8" handles most contractor pressure washers up to about 8 GPM and is easier to coil and store. Step up to 1/2" if you're running a higher-flow machine (10+ GPM) or pulling long hose runs (200 ft or more) where pressure drop across the line becomes noticeable at the gun.
What's the difference between single wire and double wire pressure washer hose?
Single wire hose has one layer of steel braid reinforcement. It's lighter, more flexible, and rated for residential and light commercial work. Double wire adds a second braid layer for higher pressure ratings and better abrasion resistance. If you're running daily commercial routes or working off concrete and gravel, double wire lasts longer and protects against blowouts at extreme pressure.
What hose do I need to pull water from a buffer tank?
You need a suction hose, not a high-pressure discharge hose. Suction lines see vacuum, not pressure, so they need a rigid spiral reinforcement that resists collapse when the pump pulls on them. Our Crushproof Suction Hose is built for exactly this job: it stays open under vacuum, handles chemicals like sodium hypochlorite, and won't kink when you drag it across the truck bed.
Can I use a pressure washer hose for soft washing?
You can, but it's overbuilt for the job. Soft wash systems run at low pressure, well under 300 PSI, far below what a wire-reinforced high-pressure hose is designed for. A dedicated soft wash hose is more flexible, easier to handle on a hose reel, and rated for the exact pressure range you're working in. For chemical transfer lines on a soft wash rig, our Clear Vinyl Braided Hose is the right call.
How long does a pressure washer hose last?
With proper care, expect years of service from a quality wire-reinforced hose like the Rampage BEAST. Hoses fail two ways: at the crimped fittings (from over-bending right at the collar) and along the jacket (from abrasion on rough surfaces). Both come down to how the hose gets used, not what it's made of. Keep it off hot concrete when you can, drain it before storage, and don't drive over it.
