The Comet BPX25 Proportioner Plumbing Kit is every hose, fitting, and clamp you need to plumb a BPX25 into a three-tank rig. It ties your water, soap, and chlorine tanks to the proportioner, then runs the proportioner to your pump, the pump to your hose reel, and the bypass back to tank. One kit, sized for the BPX25, instead of sourcing close to 30 parts one at a time.
Key Features
-
Sized for the BPX25: Every barb, hose, and clamp matches the BPX25's ports. Direct fit, no adapters.
-
Plumbs all three tanks: Water, soap, and chlorine lines, plus the pump, hose reel, and bypass. The whole setup in one box.
-
80 feet of non-collapsible hose: Five sizes, from 1" down to 1/4", so each run holds its bore under draw instead of sucking flat.
-
Stainless clamps, poly fittings: Built to take sodium hypochlorite and daily use without rusting out or cracking.
-
In-tank pickups and a 1/4" soap filter: Keep grit out of your pump, so you run fewer clogs and your pump lasts longer.
-
One kit, not a parts hunt: Stop cross-referencing fitting sizes at the hardware store. It's all here, ready to cut and clamp.
Specifications
| Fits |
Comet BPX25 proportioner |
| Setup type |
Three-tank (water, soap, chlorine) |
| Fitting material |
Poly hose barbs and uniseals |
| Clamp material |
Stainless steel |
| Hose |
Non-collapsible, five sizes (1", 3/4", 1/2", 3/8", 1/4") |
| Total hose |
80 ft |
| Chemical compatibility |
Sodium hypochlorite, surfactants, soft wash mixes |
| Hoses cut to length |
No. Ships uncut, measure and cut to your runs |
What's Included
- 2 x 1" x 3/4" hose barbs (poly)
- 2 x 3/4" hose barbs (poly)
- 1 x 1/2" x 3/8" hose barb (poly)
- 1 x 1/2" x 1/4" hose barb (poly)
- 1 x 1" hose barb elbow (poly)
- 1 x 1" x 1/2" hose barb elbow (poly)
- 2 x in-tank filter/pickups
- 2 x 3/4" uniseals
- 1 x 1/4" uniseal
- 1 x 1/4" soap filter
- 2 x 1" stainless steel hose clamps
- 2 x 3/4" stainless steel hose clamps
- 4 x 1/2" stainless steel hose clamps
- 2 x 1/4" stainless steel hose clamps
- 10 ft x 1" non-collapsible hose (proportioner to pump)
- 25 ft x 3/4" non-collapsible hose (water and chlorine inlets)
- 25 ft x 1/2" bypass hose
- 10 ft x 3/8" outlet hose (pump to hose reel)
- 10 ft x 1/4" soap hose
Hoses don't come cut to length. Every rig is plumbed a little different, so measure your runs and cut to fit.
How It Works
The kit plumbs a standard three-tank soft wash setup. The 3/4" lines feed water and chlorine into the proportioner. The 1/4" line pulls soap through its filter. The 1" line carries mixed flow from the proportioner to the pump, the 3/8" line runs pump to reel, and the 1/2" line handles your bypass back to tank. The in-tank pickups sit in each tank to keep debris out of the lines.
Measure each run on your own rig before you cut. Clamp every barb with the stainless clamps and check them after the first hour to make sure they've bedded in. Keep the soap filter clean so the line doesn't starve.
Pairs Well With
Frequently Asked Questions
Do the hoses in the BPX25 plumbing kit come cut to length?
No. The hoses ship uncut. Every rig runs its lines a little different, so you measure each run on your own setup and cut to fit. That way you're not stuck with a pre-cut length that's too short for your trailer.
What does the BPX25 proportioner plumbing kit connect?
It ties your water, soap, and chlorine tanks to the BPX25, then runs the proportioner to your pump, the pump to your hose reel, and the bypass back to tank. The fittings, clamps, filters, and hose for all of those runs are in the kit.
Is this kit chlorine safe?
Yes. The fittings are poly and the clamps are stainless, both built to hold up to sodium hypochlorite and soft wash mixes. The in-tank pickups and 1/4" soap filter also keep grit off your pump.
